Home > Miscellaneous > Other Machines Go Back
REQUEST PRICE VIEW MAP

MACHINE INFORMATION AND SPECIFICATION

  • Manufacturer:
  • OTEC
  • Model:
  • Amada PROTECTOR M42 bandsaw blade
  • Condition:
  • 1
  • YOM:
  • NA
  • Control:
  • NA
  • Price:
  • POA
  • Country:

DESCRIPTION

Amada PROTECTOR bandsaw blade exclusively for structural steel, rolled sections metal cutting Exclusively for the structural steel, strong against tooth chipping and capable of providing unparalleled high efficiency. PROTECTOR added to the back face of the tooth tip prevents excessive cutting. Suitable for: Construction Steel, Aluminium Alloys, Copper Alloys M42 High-Speed Steel Edge Unique Design Tooth Form PROTECTOR added on the back face of the tooth tip suppresses excessive cutting and prevents continuous chipping from occurring. Wide Set Available Positive Rake Tooth Angle Strong Tooth Profile As the tooth tip is made stronger, it endures impacts caused during intermittent cutting. At the same time, high cutting efficiency is assured. Set Design The broaching style set pattern was designed to eliminate pinching, therefore preventing the blade from binding in the cut. Wide Set Available When a roll-formed large-size H-beam is cut, stress relieving may occur, pinching the blade. In order to prevent damage to the blade, a “WS” (Wide Set) type is available for PROTECTOR. ADVANTAGES Extra Tough Shock Resistance Extra Tough Tooth Strippage Resistance BENEFITS Extra Fast Cutting on Structural Steel Extra Long Life in Interrupted Structural Cutting Low Cost Per Cut The hardness of the Tooth Tip represent Amada’s average value. It is adjusted to some extent according to the types and size of the products. * The WS (Wide set) type blade is a special saw blade with a measure against pinching which occurs easily when cutting the roll formed large size H-beam (applicable to H-beam whose width is over 400mm and mainly intended for that of 600mm or more width). The “PROTECTOR” WS type blade is a special saw blade with an intensified measure against pinching than the conventional WS type blade. Using of the WS type blade for cutting the material where no pinching would occur may shorten the service life of the blade. Specifications may change without notice at the sole discretion of Amada’s Engineering Department.
+ request more information

SEND ENQUIRY

*I AM A
Dealer
End User
Check here if you no longer wish to subscribe to our newsletter.

SHARE PAGE

fdbdgbdgb fxnjmynhtbgvfcd

REQUEST MORE INFORMATION

SEND ENQUIRY

*I AM A
Dealer
End User
Check here if you no longer wish to subscribe to our newsletter.

You may also be interested in these Machines

    •
      Manufacturer:
      Linde
      Model:
      Y-RE Series Cylinder
      Description:
      The Y-RE cylinder series is Kitagawa's standard close centre cylinder with built-in proximity swithcs along with built-in check and pressure relief valves. The cylinder can be bought as a a single unit or to suit a required machine under request.

      More Info

    • Manufacturer:
      Model:
      Bofors BR-1
      Description:
      {"Stock number": "180391", "Serial number": "1105", "Length": "1000mm", "Width": "900mm", "Height": "1000mm"}

      More Info

    • Manufacturer:
      Model:
      Screws to suit Gripper Jaws
      Description:
      Threaded Pads with ground faces allowing the component to be raised up from the base of the jaw. This means that it is possible to accurately hold the workpiece on less excess material.

      More Info

    • Manufacturer:
      Model:
      KSJ-212L Steel Soft Jaws 12 Inch
      Description:
      Steel serrated soft jaws to suit a 12 Inch power chuck. Jaws are manufactured from 080M15 Steel. Good Quality of of material allows for machining with a good finish.

      More Info

    SEND ENQUIRY

    *I AM A
    Dealer
    End User