"Machine is suitable for the cutting of larger spiral bevel, hypoid, and zerol bevel pinions and mating gears up to 34\u201d (863.6mm) diameter, 5\u201d (127mm) face, with 1.08 DP (module 23.5) cutting capability. CAPACITY:Extreme ratio 10:1.Roof angle range 0\u00ba to 90\u00ba. Gear diameter \u2013 Maximum\u00a0\u00a0\u00a0 34\u201d\u00a0 (863.6mm).Examples of maximum gear pitch diameters with 35\u00ba gear spiral angle using 19.7\u201d (500mm) dia. cutter at the following ratios: \u00a01 x 1 \u00a0\u2013 28.50\u201d\u00a0 (723.90mm). 2 x 1\u00a0 \u2013 34.00\u201d\u00a0 (863.60mm). 5 x 1 \u2013 34.00\u201d\u00a0 (863.60mm). Maximum radial setting **15.00\u201d**(381mm). Full depth \u2013 Maximum 1.5\u201d\u00a0 (38.1mm).Face width \u2013 Maximum 5.000\u201d\u00a0 (127mm).Coarsest Pitch (module) 1.08 DP\u00a0 (23.5 module).Index Range*5 to 80 inclusive.WORK SPINDLE:Diameter of taper hole at large end 6\u201d\u00a0 (152.4mm).Taper per foot 0.75\u201d\u00a0 (19.0mm). Depth of taper\u00a0 6\u201d\u00a0 (152.4mm).Diameter through spindle of hole 5\u201d (1270mm). CUTTER DIAMETERS:Cutter diameters utilized 9\u201d, 10.5\u201d, 12\u201d, 14\u201d, 16\u201d, 18\u201d ((200,250,320,400 & 500mm).WORKHEAD SETTINGS :Offset above center \u2013 Maximum***4.5\u201d\u00a0 (114.3mm). Offset below center \u2013 Maximum***4.5\u201d\u00a0 (114.3mm). Machine center to nose of spindle \u2013 Maximum 23.5\u201d\u00a0 (596.9mm). SPEEDS & FEEDS:Cutter speeds\u00a0 6 to 167 RPM (stepless). Cycle time, infinitely variable from 7 seconds\/tooth minimum. ELECTRICAL EQUIPMENT:Motors (60 Hz\/50 Hz ) Cutter drive motor, 15HP 1800 RPM \/1500 RPM. Hydraulic motor, 7.5HP\u00a0 1200 RPM\/1500 RPM.Coolant motor, 2HP 1200 RPM \/1500 RPM.D.C. generating drive motor, 6HP 1200 RPM * Most numbers up to 120 can also be accommodated but may require special change gears. ** This radial setting can be increased to 18.5\u201d (462.50mm) for some applications *** Maximum offset applies to pinion and gears up to 25\u201d O.D. for 34\u201d diameter gears maximum offset is 1.0\u201d Dimensions L x W x H (Floorspace) Inclusive of Hydraulic Unit, Electrical Cabinet & Swarf Conveyor. 235\u201d x 123\u201d x 92.5\u201d (5970 mm x 3120 mm x 2350mm) Approximate weight of Machine 26,682 kgs. Accessories 5,000 kgs. Machine Serial No.748301"
